Hi. I liked this post and decided to make one. Very nice Floyd. F.A.B.
So i have ordered the 'tub', i have everything for a hop strainer, tap and hopefully i will take delivery tomorrow of the tub.
My question; Can i wire my elements into a box with two switches so i can run none, one or both elements and just run that to the wall plug with ONE lead. OR, will that blow up my fuse box? Should i just run two leads to two seperate plugs as its 13 amp?
The reason for asking is i would like to make the outside of the elements silicone sealed and therefore waterproof, hence the seperate switches away trom the boiler. Also my garage has two plugs, one of which runs my fridge freezer.
If its too much load for one plug i will just seal them somehow and run two leads.
What has everyone else done with their twin element boilers?
Thanks guys.
supplying power to twin elements
Re: supplying power to twin elements
Carpking,
The answer to your question depends upon the size of the elements and the supply voltage that you use.
For a standard 2.2KW Kettle element; if you divide the wattage of the element by the voltage you get the current that the element will require, so for the 2.2KW (or 2.2 * 1000) 2200 Watts divided by 230V (in the UK) you get a current of about 9.6 Amps, So if you connected 2 of these together they would require 19 ish amps, which is obviously more than the fuse is rated at in a standard 13 Amp plug, but if you only used 1KW Elements then you would be able to get away with it.
My recomendation would be to run two seperate leads, to a seperate plugs.
Another point that you need to be aware of, is the actual supply to your garage, sometimes garages are wired from a fused spur on one of the main rings in the house, in which case this will have a 13 Amp fuse in and will cause the same problem.
I hope this has been of some help, If you require any further advice just ask.
The answer to your question depends upon the size of the elements and the supply voltage that you use.
For a standard 2.2KW Kettle element; if you divide the wattage of the element by the voltage you get the current that the element will require, so for the 2.2KW (or 2.2 * 1000) 2200 Watts divided by 230V (in the UK) you get a current of about 9.6 Amps, So if you connected 2 of these together they would require 19 ish amps, which is obviously more than the fuse is rated at in a standard 13 Amp plug, but if you only used 1KW Elements then you would be able to get away with it.
My recomendation would be to run two seperate leads, to a seperate plugs.
Another point that you need to be aware of, is the actual supply to your garage, sometimes garages are wired from a fused spur on one of the main rings in the house, in which case this will have a 13 Amp fuse in and will cause the same problem.
I hope this has been of some help, If you require any further advice just ask.
Re: supplying power to twin elements
Thanks Mike.
So this has got me thinking. I have TWO asda kettle elements. But would ONE be enough for my 23l/25l brewlengths in a 30l/35l boiler and i will keep one in reserve. The second was only to get to the boil quicker anyway. Does anyone operate that size brewlength with one asde/tesco element without problems?
Cheers.
So this has got me thinking. I have TWO asda kettle elements. But would ONE be enough for my 23l/25l brewlengths in a 30l/35l boiler and i will keep one in reserve. The second was only to get to the boil quicker anyway. Does anyone operate that size brewlength with one asde/tesco element without problems?
Cheers.
- trucker5774
- Falling off the Barstool
- Posts: 3193
- Joined: Sun May 17, 2009 12:20 pm
- Location: North Devon
Re: supplying power to twin elements
I use a boiler built in the same way. I have 2 element and a capacity of 33L. I use 2 leads for the reasons mike has calculated. I run them from the same double wall socket but I know it is on a ring main and not a spur (I built the house!). I use both elements to get things going. One is enough once the boil has started. It will just take a little longer if you use only one from the start. It is good to have a spare in the boiler though. I tend to alternate which one I use to extend their life. The set up is fine for a 5 gallon brew.Carpking wrote:Thanks Mike.
So this has got me thinking. I have TWO asda kettle elements. But would ONE be enough for my 23l/25l brewlengths in a 30l/35l boiler and i will keep one in reserve. The second was only to get to the boil quicker anyway. Does anyone operate that size brewlength with one asde/tesco element without problems?
Cheers.
John
Drinking/Already drunk........ Trucker's Anti-Freeze (Turbo Cider), Truckers Delight, Night Trucker, Rose wine, Truckers Hitch, Truckers Revenge, Trucker's Lay-by, Trucker's Trailer, Flower Truck, Trucker's Gearshift, Trucker's Horn, Truck Crash, Fixby Gold!
Conditioning... Doing what? Get it down your neck! ........
FV 1............
FV 2............
FV 3............
Next Brews..... Trucker's Jack Knife
Drinking/Already drunk........ Trucker's Anti-Freeze (Turbo Cider), Truckers Delight, Night Trucker, Rose wine, Truckers Hitch, Truckers Revenge, Trucker's Lay-by, Trucker's Trailer, Flower Truck, Trucker's Gearshift, Trucker's Horn, Truck Crash, Fixby Gold!
Conditioning... Doing what? Get it down your neck! ........
FV 1............
FV 2............
FV 3............
Next Brews..... Trucker's Jack Knife
Re: supplying power to twin elements
I am moving into a newbuild and the garage is intergral so i guess the socket will be 'ring' not 'spur'.
Re: supplying power to twin elements
I have used a single kettle element in the past but upgrading to two can knock a good half hour off a brewday. Definitely worth the effort IMO.Carpking wrote:But would ONE be enough for my 23l/25l brewlengths in a 30l/35l boiler
Kegged: 'Nowt
Bottled: Summer Lightning, Belfast Ale, JPA, Guinness Foreign Export
http://www.hopandgrain.com
Bottled: Summer Lightning, Belfast Ale, JPA, Guinness Foreign Export
http://www.hopandgrain.com