Corny Dip Tube Cleaner brush
Corny Dip Tube Cleaner brush
Hi guys, would this http://cgi.ebay.co.uk/7-Pc-Gas-Boiler-F ... 2ea01985a0 be ok to use on the long dip tube in the corny ?
Re: Corny Dip Tube Cleaner brush
I very much doubt the rod would fit, let alone the brushes.
Re: Corny Dip Tube Cleaner brush
A .22 rifle barrel cleaning brush should be about perfect for cleaning corny dip tubes
Re: Corny Dip Tube Cleaner brush
I used to own one of those and the brush was made from bronze or something similar so wouldn't it scratch the inside of the tube ?adm wrote:A .22 rifle barrel cleaning brush should be about perfect for cleaning corny dip tubes
Re: Corny Dip Tube Cleaner brush
The smallest brush size is 15mm dia surely this would fit the corny dip tube ?Northern Brewer wrote:I very much doubt the rod would fit, let alone the brushes.
Re: Corny Dip Tube Cleaner brush
Good point. Can't you get nylon or similar ones though?JULES wrote:I used to own one of those and the brush was made from bronze or something similar so wouldn't it scratch the inside of the tube ?adm wrote:A .22 rifle barrel cleaning brush should be about perfect for cleaning corny dip tubes
Re: Corny Dip Tube Cleaner brush
Dont think so they are normally bronze and there is also a wooly type as well I haven't seen a nylon barrel brush ant where but there may be one out there somewhereadm wrote:Good point. Can't you get nylon or similar ones though?JULES wrote:I used to own one of those and the brush was made from bronze or something similar so wouldn't it scratch the inside of the tube ?adm wrote:A .22 rifle barrel cleaning brush should be about perfect for cleaning corny dip tubes
Re: Corny Dip Tube Cleaner brush
I've just checked, and a .22 rimfire round will easily slip inside a cornie dip tube, but only up to the rim.
Re: Corny Dip Tube Cleaner brush
When I was in the cadets we used to clean rifles by pulling a small piece of rag through with a cord folded in the middle. Wouldn't that do the job?
Re: Corny Dip Tube Cleaner brush
I have bought this one http://cgi.ebay.co.uk/8-piece-boiler-se ... 3ca6bfa9bd as it goes down to 3/8 it should fit no prob, thanks
Re: Corny Dip Tube Cleaner brush
Yep, the .22 cleaning rod also fits, as does its associated wool mop and phosphor-bronze brushes. I'd be very reluctant to use the latter though...
Re: Corny Dip Tube Cleaner brush
I fear that it won't. 3/8 = 0.375" or 9.5mm whereas a 0.22" or 5.6mm bullet only just fits inside the tube.JULES wrote:it goes down to 3/8 it should fit no prob, thanks
- oxford brewer
- Under the Table
- Posts: 1289
- Joined: Fri Jun 09, 2006 1:00 pm
- Location: oxford
Re: Corny Dip Tube Cleaner brush
I bought one of these camelbak and use the tube brush for my corny out tube and other various tubing.
Only the fool, in the abundance of water is thirsty!!
The Right Honourable Robert Nesta Marley
Drinking
Fermenting
Conditioning
The Right Honourable Robert Nesta Marley
Drinking
Fermenting
Conditioning
Re: Corny Dip Tube Cleaner brush
Strip the earth wire from 1.5mm twin and earth feed it through the tube, make a 'U' in one end to grip a piece of J cloth soaked in cleaner and pull it through.
or
Get a piece of carbon fiber as to tension kites and push a bung of J cloth through.
or
Get a piece of carbon fiber as to tension kites and push a bung of J cloth through.
Re: Corny Dip Tube Cleaner brush
lidl are selling a brush at the moment that fits perfectly in the dip tube.
I think they are less than a quid!
I think they are less than a quid!