Brewbuilder 3kW Elements - Cable Gland Size needed
-
- Steady Drinker
- Posts: 70
- Joined: Mon Jun 22, 2015 1:34 pm
Brewbuilder 3kW Elements - Cable Gland Size needed
Hi,
I've just pulled the trigger on a new boiler setup from Brewbuilder and wondered if anyone could tell me the size of cable gland required for the 3kw bendy LWD elements?
Looking forward to some new shiny!
Thanks all,
Jamie.
I've just pulled the trigger on a new boiler setup from Brewbuilder and wondered if anyone could tell me the size of cable gland required for the 3kw bendy LWD elements?
Looking forward to some new shiny!
Thanks all,
Jamie.
-
- Drunk as a Skunk
- Posts: 996
- Joined: Sat Jul 21, 2012 11:12 pm
- Location: Garden of England
Re: Brewbuilder 3kW Elements - Cable Gland Size needed
hey, you want an M20 to fit a cable diameter of ~10mm
literally just got mine up and running with my new PWM controller. hell of a stepup from kettle elements!!
literally just got mine up and running with my new PWM controller. hell of a stepup from kettle elements!!
dazzled, doused in gin..
-
- Steady Drinker
- Posts: 70
- Joined: Mon Jun 22, 2015 1:34 pm
Re: Brewbuilder 3kW Elements - Cable Gland Size needed
Excellent - thanks, I've been looking at stainless glands and almost fell off my chair with the price!
I'm moving up from a 2.4kw element and hope to get a more vigorous boil on my double batches (about 50l in the boiler).
Good luck with your new build
I'm moving up from a 2.4kw element and hope to get a more vigorous boil on my double batches (about 50l in the boiler).
Good luck with your new build
- Wonkydonkey
- Drunk as a Skunk
- Posts: 847
- Joined: Sat Mar 01, 2014 9:37 am
- Location: In the Stables
Re: Brewbuilder 3kW Elements - Cable Gland Size needed
I've got a 3kw pigtail in a Thermopot, I get a good boil of 60-65 Lt I even have to turn it down after the first 15 mins from 12.4 amps to about 6 or 7 amps. (I have a amp meter)
Well worth all the hasle of building the system
Well worth all the hasle of building the system
To Busy To Add,
-
- Steady Drinker
- Posts: 70
- Joined: Mon Jun 22, 2015 1:34 pm
Re: Brewbuilder 3kW Elements - Cable Gland Size needed
Interesting - I was getting a semi-rolling boil on my 2.4kw element so had hoped for something more vigorous. You have me worried that it will be too vigorous now!
My control panel doesn't allow me to dial back unfortunately, I'll have to see how this works in practice and then do some jiggery pokery where required!
My control panel doesn't allow me to dial back unfortunately, I'll have to see how this works in practice and then do some jiggery pokery where required!
Re: Brewbuilder 3kW Elements - Cable Gland Size needed
*removed* Didn't see the word bendy there...
I like beer --- Currently rebuilding the brewery, this time with stainless...
- Wonkydonkey
- Drunk as a Skunk
- Posts: 847
- Joined: Sat Mar 01, 2014 9:37 am
- Location: In the Stables
Re: Brewbuilder 3kW Elements - Cable Gland Size needed
HairyJamie wrote:Interesting - I was getting a semi-rolling boil on my 2.4kw element so had hoped for something more vigorous. You have me worried that it will be too vigorous now!
My control panel doesn't allow me to dial back unfortunately, I'll have to see how this works in practice and then do some jiggery pokery where required!
My pot is insulated, but I could boil it at full power, I like to save a bit of power, but it would just mean I'd lose more in evaporation. Also if I do 25Lts then it's better to back off on the power, I have a pid, which you can reduce the power output in percentages, but I also have one of those big 4k dimmer things from China, but it needed a fan as the heatsink was not big enough. I prefer the dimmer as it's just a dial to twist, the PID is for mash temp water
I don't know your system, but I'm pretty sure you will be ok.
To Busy To Add,
-
- Steady Drinker
- Posts: 70
- Joined: Mon Jun 22, 2015 1:34 pm
Re: Brewbuilder 3kW Elements - Cable Gland Size needed
Cheers, my new control panel has three pids but at the moment only the hlt is actually controlled by an SSR.
Anyone know if the inkbird pids can dial back power using pwm ?
Sent from my Moto G (4) using Tapatalk
Anyone know if the inkbird pids can dial back power using pwm ?
Sent from my Moto G (4) using Tapatalk
Re: Brewbuilder 3kW Elements - Cable Gland Size needed
What cable do you use to the 3kw elements
- themadhippy
- Even further under the Table
- Posts: 2951
- Joined: Tue Dec 08, 2009 12:53 am
- Location: playing hooky
Re: Brewbuilder 3kW Elements - Cable Gland Size needed
In the uk a minimum of 1.5mm,heat proof flex,something like https://www.tlc-direct.co.uk/Products/C ... ash50.htmlWhat cable do you use to the 3kw elements
Warning: The Dutch Coffeeshops products may contain drugs. Drinks containing caffeine should be used with care and moderation
Re: Brewbuilder 3kW Elements - Cable Gland Size needed
HairyJamie wrote:Cheers, my new control panel has three pids but at the moment only the hlt is actually controlled by an SSR.
Anyone know if the inkbird pids can dial back power using pwm ?
Sent from my Moto G (4) using Tapatalk
Hi, This is Marina from Inkbird. I want to help you out with this issue.
Could you please make it more clear, I do not understand your questions well, sorry!