Jim's Beer Kit

Hi folks, Hopefully a quick question... Does anyone know where I can get hold of a new rubber one way valve for an auto syphon? Mine has split and it seems a bit of a waste of a perfectly good piece of kit to have to replace the whole thing when it's just a small bit of rubber which needs replacing ...

Hi folks, I just wondered if anyone knows of a way to clean a corny keg without moving it. I've currently got 5 kegs in my keezer and it's a nice snug fit (also a major pain in the rear to try and get one out if needed) Ideally I just need some advice on a way, if there is one, to clean these kegs w...

It was working fine up until last night. I'll try and take it out and check for loose connections. Ideally I'd actually like to change all 5 boards as some of the others also seem a little dimmer than the others

Hi folks, First of all I apologise if this is the wrong place to ask this question and, if so, I ask if you can point me in the right direction for this question... I have a 5 tap t-bar with oval 'fisheye' badges. One of the LED boards behind a badge has stopped working. Would anyone know where I ca...

OK that's a good call. I'll see if I can fit the DJ on there then. I've got 5 cornies in the Keezer that only just fit when they're all in but have a few pockets of space here on there to fit a 2 litre bottle but hopefully may fit a DJ filled with water in. Will try once I've got them all filled wit...

Ah yes, that's a good idea. But would that not only read the temperature lower down due to the height of the demijohn and not level the temperature in the whole Keezer? I've currently got my probe attached to the side of a 2 litre bottle filled with water (probe pointing away from the bottle so to r...

Hi folks, So I've recently done my keezer and had some great beers from it. Trouble is my inkbird control unit reads a totally different temperature at the top of the Keezer to the bottom of the Keezer and because of this my lagers have frozen when the keg gets low. How do I get the temperature all ...

Ah I see, I think

Thank you so much for your detailed reply. I'll take a closer look at the one you've linked

Thanks for your help and speedy response

Kind regards,

Hi folks, Sorry if this has been asked and answered before but I am getting a little confused with things. I've got a 5 tap T-Bar with light up badges. When I got the tap the LED driver/transformer was not supplied and I'm trying to figure out what power rating I need. I've read 24VAC but the bit th...

Hi folks, Sorry to post this here but I couldn't find a more fitting thread... I live in Lincoln and am finding it impossible to get a 6kg co2 bottle. Calor say they have some but will only trade with me if I have an air liquide one to return. I'm not keen on using the eBay sellers for co2 as I've b...

Well I found my leak!! On the 3rd reg (one on the left with no gauge) there was a leak around the line inlet. I found it by using a brush and very soapy water. The first time I tried the soapy water technique I used a spray bottle and my soapy water mixture must have been too dilute. I'm surprised I...

All the fittings are 3/8 push fit type. I'm not sure if the middle reg is John Guest fittings but 3/8 push fit all the same. I'll give the soapy water with a brush trick a try. I used soapy water in a spray bottle before and it didn't show up anything. I've looked at the set up just now and both of ...

Just checked the regs this morning and all are showing 0psi. I've switched the master reg back on to refill the lines with pressure and the regs are reading 10 and 20 psi as they're set to. I've switched off each secondary reg so that there's no pressure going to the beer/wine. Will check again arou...

Hi all, First of all, thanks for answering all my previous questions. I don't think I ask questions which have already been answered if I'd researched but I believe my questions are usually quite unusual. This one is quite interesting (or so it is to me anyway!) I have a 4 regulator set up: http://i...

I would buy a 310 but have a decent 210 with spare holes ready for a 3rd coil (I fitted a new thermostat when I first got it and it works a dream!). I've had a 310 before but with just 1 product line (which was strange!). I'd be happy to swap with anyone who fancies it?? :lol: Picture as promised. T...