Jim's Beer Kit

Would pure sodium precarbonate would better then ? What brands have you found to be less foamy then or monster foamy

I understand how my pump works better now

Well im using the same pump as the grainfather and a similiar length cfc so fingers crossed may even use soda crystals like i currently do

My pump is magnetically coupled so no bearings ?

Thanks everyone for their replies and thoughts. I've gone off the idea of the Aliexpress SS CFC now , I'm much more inclined to try and make my own wit some copper pipe, hose and fittings. Chastuck - that is a thing of beauty! Kev888 - i'd discounted a plate chiller because of sanitation concerns, ...

If your water flow rate is low it would be worth getting your water board to do a flow test. There's a minimum flow rate which the board is required to provide. Can't remember what it is. It will be tested for free. If it's a problem with the supply it will be fixed for free. The flow rate here is ...

Yep as atb says its too short, id buy another pump off there in a heart beat. But some things you may save a couple of quid but wait 30 days for it to come

I will be using 20mm id rubber hose and 10mm copper pipe but dont think ill be wrapping wire the pipe mainly as i dont have a blow torch for soldering. It will ten metres in unwrapped form wort thru the top cold water thru bottom.

https://www.ebay.co.uk/itm/Stainless-steel-corrugated-pipe-Solar-DN-16-20-25/173165946601? £2.38 a meter, postage sucks though & the end couplers aren't all that cheap but its fully autoclavable (assuming you have a large enough clave). Most CFCs have a bracket or some sort to hold them in a coil, ...

HairyJamie wrote: ↑

Sun Jun 17, 2018 10:14 pm

Wow that looks a belter! Does it stay in the pot? Is the pot used for the boil? Interested!

Sent from my moto g(6) using Tapatalk

Wait till you see the price of solar hose

aamcle wrote: ↑

Sun Jun 17, 2018 6:19 pm

If I recall correctly and I may not the one you want is a M20, the actual ID is about 21mm. I think that is what I bought.


Aamcle

Ive seen m20 being banded about so i think your atb

Follow me twitter @streetbrewer28 for the pics

Yep you will need
4 x 15mm x 10mm copper reducers (toolstation)
2 x stainless steel 1/2 " equal tees
2 x stainless steel 1/2" x 20mm hose barbs
Jubilees clips and cable ties
10mm micropore copper pipe
3/4" hose pipe
Ball valve tap

Any more questions fire away im half way thru my build

Well this alot harder than i thought think ill go wilko and play lets see what fits then order a4 grade washers

I was donated a false bottom and recenttly bpught a 1/2 street elbow but the elbow falls thru the centre hole. So i need a pack of stainless washers. But no idea what size to buy as stated the elbow is 1/2.

Thank in andance sean

https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.co.uk%2Fulk%2Fitm%2F112879584474 1/2” nut? Sent from my iPhone using Tapatalk Pro After i put out that comment out my brain farted and i found that nut after searching hex nut, but before that i could only find big nuts that goes on a b...

on mine i use a couple of different setups depending on what vessel im using, goes something like this , either a male female coupler , male end down through the hole and a nut to secure it to the fb , then an elbow and a hose tail. Or if im using the flat bottom pot , a street elbow , male side in...