Using my time more effectively...
Using my time more effectively...
Hi all,
For the past 15 months I have struggled to brew due to the arrival of a new family member and an increase in my work load from my employer. Because of all this brewing has become less of a priority in comparison to my other hobbies (marathon running and video games - sacrilege, I know).
So with that in mind I am thinking of ways to cut back on the amount of time a brew day takes, so that I can fully utilise my spare time. Do the following seem ok (sorry if these are recycled questions in anyway).
1. Can I fill my kettle the night before with water, leave it for 24 hours, and then have a timer turn it on when I am on my way home?
2. I have recently installed a new combi boiler, can I fill up directly from the hot water tap to help with reduction of time, is it ok to use this water.
Thanks
Manngold
For the past 15 months I have struggled to brew due to the arrival of a new family member and an increase in my work load from my employer. Because of all this brewing has become less of a priority in comparison to my other hobbies (marathon running and video games - sacrilege, I know).
So with that in mind I am thinking of ways to cut back on the amount of time a brew day takes, so that I can fully utilise my spare time. Do the following seem ok (sorry if these are recycled questions in anyway).
1. Can I fill my kettle the night before with water, leave it for 24 hours, and then have a timer turn it on when I am on my way home?
2. I have recently installed a new combi boiler, can I fill up directly from the hot water tap to help with reduction of time, is it ok to use this water.
Thanks
Manngold
Re: Using my time more effectively...
Use a timer on your kettle. Works for me. Also, batch sparging is much quicker and less of a faff.
- alexlark
- Under the Table
- Posts: 1403
- Joined: Thu May 02, 2013 12:29 pm
- Location: Rhondda, South Wales
Re: Using my time more effectively...
And yes you can use the combi. Turn the water temp to max and run the tap a bit slower. Put the water temp back as it was afterwards.
-
- Lost in an Alcoholic Haze
- Posts: 677
- Joined: Tue May 05, 2015 11:21 am
Re: Using my time more effectively...
I fill the kettle the night before, and put it on a timer plug. 90 mins to get it to strike temp. Grain pre weighed and ready to mash in
Using my time more effectively...
Filling the kettle the night before also lets you do any water treatment then, if you need to, without adding to the time on brew day. Any prep like that (another being putting the grains out) helps a lot I find, either by cutting down brew day length or enabling you to get on with other things during the mash etc.
Re: Using my time more effectively...
Brilliant, thanks guys. For the record, is filling from the outside tap an issue?
thanks
thanks
-
- Drunk as a Skunk
- Posts: 996
- Joined: Sat Jul 21, 2012 11:12 pm
- Location: Garden of England
Re: Using my time more effectively...
since i went BIAB/nochill i've got so much time kicking my heels on brewday i've thought about digging out the PS2..
dazzled, doused in gin..
Re: Using my time more effectively...
Not unless it's fed from your septic tank or something!Manngold wrote:Brilliant, thanks guys. For the record, is filling from the outside tap an issue?
thanks
-
- Telling imaginary friend stories
- Posts: 5229
- Joined: Sun Oct 16, 2011 1:49 pm
- Location: Cowley, Oxford
Re: Using my time more effectively...
you can get foodsafe blue hose for drinking water (brewing water) from caravan suppliers on ebay
all good solutions just ensure any timers or automatic switches you use are rated to switch on and off the load your heating elements and controller will draw, most segment timers are rated 10a or less.. a cheap(er) diy timer solution is an ebay central heating/water tank segment timer
all good solutions just ensure any timers or automatic switches you use are rated to switch on and off the load your heating elements and controller will draw, most segment timers are rated 10a or less.. a cheap(er) diy timer solution is an ebay central heating/water tank segment timer
ist update for months n months..
Fermnting: not a lot..
Conditioning: nowt
Maturing: Challenger smash, and a kit lager
Drinking: dry one minikeg left in the store
Coming Soon Lots planned for the near future nowt for the immediate
Fermnting: not a lot..
Conditioning: nowt
Maturing: Challenger smash, and a kit lager
Drinking: dry one minikeg left in the store
Coming Soon Lots planned for the near future nowt for the immediate
-
- Drunk as a Skunk
- Posts: 904
- Joined: Tue Jan 15, 2013 11:42 am
- Location: Newton-le-Willows ( St Helens/Warrington)
Re: Using my time more effectively...
one more, try "no chill" into a container it saves time on the hot side day and you can get the fermentation going later when it's convenient.
No Chill - http://www.brewersfriend.com/2009/06/06 ... ue-tested/
#ATB. aamcle
No Chill - http://www.brewersfriend.com/2009/06/06 ... ue-tested/
#ATB. aamcle
- Jocky
- Even further under the Table
- Posts: 2738
- Joined: Sat Nov 12, 2011 6:50 pm
- Location: Epsom, Surrey, UK
Re: Using my time more effectively...
Here's my tips:
1. Get everything you can prepped the night before. Grains weighed and crushed, water treatment measured etc, equipment all laid out in the right place.
2. Either fill from the boiler (as long as it's a combi, tank based systems aren't safe as far as I know) or as you have thought, set it up on a timer.
3. No sparge. Or do a single batch sparge. Basically you can mash with your full volume of water if you have a big enough tun. You'll just need a little more grain to cope with the efficiency loss.
4. 30 minute boil. Yes 60 minute is ideal, but once you have a rolling boil 30 minutes should be fine as long as it's open.
5. A time to lean is a time to clean. If the boil is on you should be cleaning your mash tun out.
6. Get a good chiller. If you have a decent immersion chiller and you stand over the pot jiggling it up and down you'll get down to temperature rapidly (10 minutes or less).
7. Get decent cleaning chemicals. I love PBW. It's expensive but I don't need a lot and it just does the job so well.
8. Keep some old tea towels for drying. It'll help dry your equipment so you can put it away faster.
1. Get everything you can prepped the night before. Grains weighed and crushed, water treatment measured etc, equipment all laid out in the right place.
2. Either fill from the boiler (as long as it's a combi, tank based systems aren't safe as far as I know) or as you have thought, set it up on a timer.
3. No sparge. Or do a single batch sparge. Basically you can mash with your full volume of water if you have a big enough tun. You'll just need a little more grain to cope with the efficiency loss.
4. 30 minute boil. Yes 60 minute is ideal, but once you have a rolling boil 30 minutes should be fine as long as it's open.
5. A time to lean is a time to clean. If the boil is on you should be cleaning your mash tun out.
6. Get a good chiller. If you have a decent immersion chiller and you stand over the pot jiggling it up and down you'll get down to temperature rapidly (10 minutes or less).
7. Get decent cleaning chemicals. I love PBW. It's expensive but I don't need a lot and it just does the job so well.
8. Keep some old tea towels for drying. It'll help dry your equipment so you can put it away faster.
Ingredients: Water, Barley, Hops, Yeast, Seaweed, Blood, Sweat, The swim bladder of a sturgeon, My enemies tears, Scenes of mild peril, An otter's handbag and Riboflavin.
- Dennis King
- Telling everyone Your My Best Mate
- Posts: 4227
- Joined: Sat Aug 11, 2007 7:52 pm
- Location: Pitsea Essex
Re: Using my time more effectively...
Have you thought about overnight mashing?
Re: Using my time more effectively...
or even mashing and sparging on an evening and boiling in a morning? splits up a brew day nicely, i haven't used the immersion chiller on the last few brews either, just drained into the fermenter and pitched the yeast when the temps are suitable. i'm in the same boat, with a 2 year old toddler- he loves putting the hops in.Dennis King wrote:Have you thought about overnight mashing?
Planning: BrewEasy system build; possibly a Wychwood Hobgoblin Gold clone
Fermenting: Simcoe SMASH
Drinking: Cascade Centennial Pale
Fermenting: Simcoe SMASH
Drinking: Cascade Centennial Pale
-
- Falling off the Barstool
- Posts: 3557
- Joined: Fri Nov 23, 2007 5:30 pm
- Location: Fort Wayne, Indiana
Re: Using my time more effectively...
Will you be filtering this water? Is it chlorinated?Manngold wrote:Hi all,
I have recently installed a new combi boiler, can I fill up directly from the hot water tap to help with reduction of time, is it ok to use this water.
Thanks Manngold
Same questions about the water from the outside tap.
I'm just here for the beer.