Where to drill holes

The forum for discussing all kinds of brewing paraphernalia.
Post Reply
User avatar
k1100t
Piss Artist
Posts: 223
Joined: Sat Apr 24, 2010 12:59 am
Location: Cambridge, UK
Contact:

Where to drill holes

Post by k1100t » Wed Oct 25, 2017 3:28 pm

I started collecting bits and bobs to rebuild the brewery earlier in the year and have had everything, apart from tubing, for months. I can't seem to bring myself to drill holes in all those lovely shiny stainless pots. I think what's stopping me is not knowing exactly where to drill the holes. My anxious predictions are saying that I'll drill in the wrong place and ruin my pots, damn brain.

Anyway, I would like to have a bash at getting one of the pots up and running. I have a MattMill Läuterhexe to connect to a 3/4" 2 piece tap, and a 3KW element from MrLard to fit to the boiler, plus another 3/4" 2 piece tap to fit high up for returning.

Firstly a question about the orientation of the pot. I've seen lots of photos where the bottom tap is centred between the handles, or directly under a handle. Does it really matter...?

How high up do you put the element...? I need to leave enough space for the Läuterhexe to fit underneath, but do I need to leave a certain amount of space between the bottom of the pot and the element?

Finally, the Läuterhexe sits on the bottom of the pot, so I'm assuming I try and fit the tap as low down as physically possible?

Thanks,
I like beer --- Currently rebuilding the brewery, this time with stainless...

User avatar
Rogermort
Piss Artist
Posts: 142
Joined: Tue Jan 13, 2015 9:56 pm
Location: Rutland, England (not Vermont)

Re: Where to drill holes

Post by Rogermort » Wed Oct 25, 2017 11:04 pm

Low as you can get both without them touching to reduce dead space.


Sent from my iPad using Tapatalk

Secla
Lost in an Alcoholic Haze
Posts: 637
Joined: Thu Dec 04, 2008 1:26 am

Re: Where to drill holes

Post by Secla » Wed Oct 25, 2017 11:57 pm

if you can get q-max cutters they make the job alot easier and neater aswell

Fil
Telling imaginary friend stories
Posts: 5229
Joined: Sun Oct 16, 2011 1:49 pm
Location: Cowley, Oxford

Re: Where to drill holes

Post by Fil » Thu Oct 26, 2017 12:00 am

Imho Take your time planning out different options, consider the minimum brewlength your likely to want to brew and as long as the element is well submerged at that volume feel totally free to mount it above your filter.

If still in doubt lay out the bits in the pot base to illustrate positions and take a few snaps for comment ;)

But if you do screw up and put a hole in the wrong place. its not the end of the world SS nuts bolts and washers or even SS or brass plumbing fittings such as lock nuts and blanking plates can be used to close off holes.Tho an emergency dump valve port is also another useful disguise for a screw up ;)

As for handle position, Its upto you, if useing bergland pots just dont try to use the handles with full pots they are not designed to support that sort of mass. Pot handles can serve as useful places to hang thermometer probes or act as rests for recirc return tubing, consider them as part of your brewday process and use them to your best advantage ;)
ist update for months n months..
Fermnting: not a lot..
Conditioning: nowt
Maturing: Challenger smash, and a kit lager
Drinking: dry one minikeg left in the store
Coming Soon Lots planned for the near future nowt for the immediate :(

User avatar
k1100t
Piss Artist
Posts: 223
Joined: Sat Apr 24, 2010 12:59 am
Location: Cambridge, UK
Contact:

Re: Where to drill holes

Post by k1100t » Thu Oct 26, 2017 11:43 am

Secla wrote:
Wed Oct 25, 2017 11:57 pm
if you can get q-max cutters they make the job alot easier and neater aswell
I have a 2mm pilot drill bit, a stepped drill bit and q-max cutters. Hardware isn't the problem. the problem is between the keyboard and chair... :roll:

Cheers,
I like beer --- Currently rebuilding the brewery, this time with stainless...

User avatar
k1100t
Piss Artist
Posts: 223
Joined: Sat Apr 24, 2010 12:59 am
Location: Cambridge, UK
Contact:

Re: Where to drill holes

Post by k1100t » Mon Apr 13, 2020 9:01 am

Well... The pots and fixings have been sitting in the shed long enough. I suppose it's about time I actually extracted my finger from my arse and drilled some holes. To the shed!

Shame I can't quite remember how I was going to set everything up...
Last edited by k1100t on Tue Apr 14, 2020 10:45 am, edited 1 time in total.
I like beer --- Currently rebuilding the brewery, this time with stainless...

Nitro Jim
Piss Artist
Posts: 182
Joined: Wed Feb 18, 2015 6:10 pm
Location: Spalding, Lincolnshire

Re: Where to drill holes

Post by Nitro Jim » Mon Apr 13, 2020 9:28 am

k1100t wrote:
Mon Apr 13, 2020 9:01 am
Well... The pots and fixing have been sitting in the shed long enough. I suppose it's about time I actually extracted my finger from my arse and drilled some holes. To the shed!

Shame I can't quite remember how I was going to set everything up...
Blimey, 2 and a half years later...

Good luck!

I bet your finger, your arse or both are sore! :)
Beer is my drug of choice.
I don't need anger management classes, I need people to stop pissing me off.

No beer, no fun - know beer, know FUN!

Carrots may be good for your eyes but alcohol is better as it gives you double vision!

User avatar
k1100t
Piss Artist
Posts: 223
Joined: Sat Apr 24, 2010 12:59 am
Location: Cambridge, UK
Contact:

Re: Where to drill holes

Post by k1100t » Mon Apr 13, 2020 9:45 am

Yeah, still haven't had the shed electrics fixed four years after blowing them either... 🙄
I like beer --- Currently rebuilding the brewery, this time with stainless...

User avatar
k1100t
Piss Artist
Posts: 223
Joined: Sat Apr 24, 2010 12:59 am
Location: Cambridge, UK
Contact:

Re: Where to drill holes

Post by k1100t » Tue Apr 14, 2020 10:45 am

Two broken 2mm cobalt bits later, ta da, a Hot Liquor Tank! Needs a good clean now, and all the fixtures fitted properly, but you get the idea.

Image

My notes, what I managed to find anyway, make mention of a pukka pick-up, which I assume I was going to stick on the inside of the tap. Can't find any evidence of a product matching that name, so I used a spare nut to hold the tap in place for the photos... 🤷‍♂️

Image

While I was at it, I also added gubbins to the water filter housing and the plate chiller. Yes, it's a small one, but I was gifted it and it's all I've got or can afford for the moment...

Image

Best order some more 2mm pilot hole drill bits, so I can finish off the other two pots.
I like beer --- Currently rebuilding the brewery, this time with stainless...

User avatar
k1100t
Piss Artist
Posts: 223
Joined: Sat Apr 24, 2010 12:59 am
Location: Cambridge, UK
Contact:

Re: Where to drill holes

Post by k1100t » Sun Apr 19, 2020 7:54 am

Found some time yesterday to finish drilling hole in the other pots. Turns out that the step drill bit worked better at higher RPM, so the final pot was drilled in about a minute, rather than about half an hour. 🤷‍♂️

Image
I like beer --- Currently rebuilding the brewery, this time with stainless...

User avatar
orlando
So far gone I'm on the way back again!
Posts: 7197
Joined: Thu Nov 17, 2011 3:22 pm
Location: North Norfolk: Nearest breweries All Day Brewery, Salle. Panther, Reepham. Yetman's, Holt

Re: Where to drill holes

Post by orlando » Mon Apr 20, 2020 7:33 am

Try using the elbow in the HLT to see if that could be used as a pick up tube. If it gets close to the botom of the pot it works really well. It's all I use, works brilliantly.
I am "The Little Red Brooster"

Fermenting:
Conditioning:
Drinking: Southwold Again,

Up Next: John Barleycorn (Barley Wine)
Planning: Winter drinking Beer

User avatar
k1100t
Piss Artist
Posts: 223
Joined: Sat Apr 24, 2010 12:59 am
Location: Cambridge, UK
Contact:

Re: Where to drill holes

Post by k1100t » Mon Apr 20, 2020 8:16 am

orlando wrote:
Mon Apr 20, 2020 7:33 am
Try using the elbow in the HLT to see if that could be used as a pick up tube.
I think my original idea was to use a 45° angle and a ground down full bore hose tail. Will see if I have a spare 90° angle kicking about to try it though.
I like beer --- Currently rebuilding the brewery, this time with stainless...

nibber
Steady Drinker
Posts: 46
Joined: Thu Aug 13, 2009 10:46 pm
Location: Ashford,Kent.

Re: Where to drill holes

Post by nibber » Thu Apr 23, 2020 8:00 pm

Nice job,good luck with the brewing!😀🍺

Post Reply