Herms advice plz

The forum for discussing all kinds of brewing paraphernalia.
Post Reply
D4V33
Steady Drinker
Posts: 47
Joined: Sun Apr 19, 2020 9:20 pm

Re: Electric HERMS build

Post by D4V33 » Mon Apr 27, 2020 9:39 pm

Ok, so got a good few parts ordered - false bottom, hoses, quick disconnects, pump and still need to get an element for the kettle.

So far I’ve finished the HLT and fitted a couple of valves with pick up tube and whirlpool inlet to the kettle.
Last edited by D4V33 on Sun May 10, 2020 1:11 pm, edited 2 times in total.
Top
User avatar
LeeH
Under the Table
Posts: 1921
Joined: Wed Jan 11, 2012 9:42 pm
Location: North Lincs
Contact:
Contact LeeH

Electric HERMS build

Post by LeeH » Tue Apr 28, 2020 10:13 am

A very tidy job so far.
Sabro Single Hop NEIPA 25/02/20 CLICK ME to monitor progress with Brewfather & iSpindel
Top
User avatar
k1100t
Piss Artist
Posts: 223
Joined: Sat Apr 24, 2010 12:59 am
Location: Cambridge, UK
Contact:
Contact k1100t

Re: Electric HERMS build

Post by k1100t » Tue Apr 28, 2020 11:12 am

D4V33 wrote: ↑
Mon Apr 27, 2020 9:39 pm
 So far I’ve finished the HLT and fitted a couple of valves with pick up tube and whirlpool inlet to the kettle.
Where did you get the pickup and whirlpool inlet from? Not seen ones looking like that before...
I like beer --- Currently rebuilding the brewery, this time with stainless...
Top
User avatar
mozza
Under the Table
Posts: 1031
Joined: Thu Jan 31, 2013 7:58 pm
Location: Essex

Re: Electric HERMS build

Post by mozza » Tue Apr 28, 2020 7:56 pm

Very smart looking build
Cheers and gone,

Mozza
Top
D4V33
Steady Drinker
Posts: 47
Joined: Sun Apr 19, 2020 9:20 pm

Re: Electric HERMS build

Post by D4V33 » Wed Apr 29, 2020 7:31 am

k1100t wrote: ↑
Tue Apr 28, 2020 11:12 am
D4V33 wrote: ↑
Mon Apr 27, 2020 9:39 pm
 So far I’ve finished the HLT and fitted a couple of valves with pick up tube and whirlpool inlet to the kettle.
Where did you get the pickup and whirlpool inlet from? Not seen ones looking like that before...
Cheers guys, really enjoying g the build and can’t wait to test it.

The inlet and outlet within the kettle where just made out of some left over sections of stainless I had from an old job I did.

Once it’s all built and tested, I’ll right up everything I used to build this setup.

Cheers
Top
User avatar
k1100t
Piss Artist
Posts: 223
Joined: Sat Apr 24, 2010 12:59 am
Location: Cambridge, UK
Contact:
Contact k1100t

Re: Electric HERMS build

Post by k1100t » Wed Apr 29, 2020 11:12 am

D4V33 wrote: ↑
Wed Apr 29, 2020 7:31 am
 The inlet and outlet within the kettle where just made out of some left over sections of stainless I had from an old job I did.
Nice work!
I like beer --- Currently rebuilding the brewery, this time with stainless...
Top
Post Reply

Return to “Brewing Equipment”