Cleaning boilers / lauter

The forum for discussing all kinds of brewing paraphernalia.
User avatar
bitter_dave
Even further under the Table
Posts: 2170
Joined: Thu Dec 29, 2005 1:00 pm
Location: Whitley Bay

Cleaning boilers / lauter

Post by bitter_dave » Sun Feb 19, 2006 4:35 pm

Any advice on cleaning boilers (my boiler did not come with instructions)? My first boil has really taken the shine of the element, although i guess that's pretty normal. Before the boil I took the advice of the home-brew-shop-guy and did a quick clean / sterilise (VWP) - quick so as to not damage the element too much.

My 'lauter' - two 30 litre fermenting bins with the inner one with 2mm holes drilled in the base - was a bit of a disapointment. Black malt got stuck in the holes, clogging it up when I was trying to drain the wort off the hops / black malt (the rest being extract). :bonk May have to think about getting a grain bag for my upcoming AG, and sparging Jim-style.

User avatar
Andy
Virtually comatose but still standing
Posts: 8716
Joined: Fri Nov 18, 2005 1:00 pm
Location: Ash, Surrey
Contact:

Post by Andy » Sun Feb 19, 2006 4:43 pm

Regarding the element, I took some DaaB advice and added some citric acid to boiling water just covering the element. In a couple of minutes the element was looking like new again.

I don't go big on boiler santisation, in fact I don't bother. Just make sure it's clean, the 90 minute boil will finish off anything which might have had beer spoiling ambitions. :D

User avatar
Jim
Site Admin
Posts: 10312
Joined: Sun Aug 22, 2004 1:00 pm
Location: Washington, UK

Post by Jim » Sun Feb 19, 2006 4:55 pm

I just wipe off the worst of the crud around the rim with a washing up sponge and give it a good rinse. Like Andy says, the next boil sterilise any nasties that get onto it.

I always remove the element and clean it very gently with a plastic scourer (don't go mad, or you'll take off the plating). Cleaning the element is very important, especially if you live in a hard water area - the build up of scale will make the element overheat and reduce it's life.

BlightyBrewer

Post by BlightyBrewer » Sun Feb 19, 2006 5:24 pm

I soaked in soda crystals for 15-20 mins, wiped over with a soft cloth to remove crud, then I ran the solution throught the counterflow chiller. I then rinsed and boiled some water in the boiler with the lid on (which gave it a steam clean) and ran this through the chiller to finish...all sparkling clean. :D

User avatar
bitter_dave
Even further under the Table
Posts: 2170
Joined: Thu Dec 29, 2005 1:00 pm
Location: Whitley Bay

Post by bitter_dave » Sun Feb 19, 2006 6:13 pm

Excellent, lotsa options - thanks ;) I think I'll give the citric acid thing a go as it sounds like instant satisfaction.

I think I might give my lauter another go as I think it was only the black malt blocking up the holes - and no black malt used in the next attempt. I might increase the size of the holes from 2 to 3 mm.

Out of interest, I've never seen a grain bag - how big are the holes?

User avatar
FlippinMental
Hollow Legs
Posts: 337
Joined: Wed Mar 08, 2006 1:00 pm

Post by FlippinMental » Tue Mar 14, 2006 10:59 pm

have just got an old SWAN boiler working. i've noticed a small speak on the element, which looks like the plating has come away. does this spell death for the element or is it ok to use?
FM

User avatar
Andy
Virtually comatose but still standing
Posts: 8716
Joined: Fri Nov 18, 2005 1:00 pm
Location: Ash, Surrey
Contact:

Post by Andy » Tue Mar 14, 2006 11:09 pm

My Swan boiler has lost a fair bit of the initial element plating but all is well. Post a pic up....

User avatar
FlippinMental
Hollow Legs
Posts: 337
Joined: Wed Mar 08, 2006 1:00 pm

Post by FlippinMental » Tue Mar 14, 2006 11:50 pm

QUOTE (andy @ Mar 14 2006, 10:09 PM) My Swan boiler has lost a fair bit of the initial element plating but all is well. Post a pic up....
Image

would appreciate your opinion, andy. have ringed the spot where the plating has come away.
FM

User avatar
FlippinMental
Hollow Legs
Posts: 337
Joined: Wed Mar 08, 2006 1:00 pm

Post by FlippinMental » Wed Mar 15, 2006 7:23 pm

thanks Daab, i'll give that a go.

User avatar
Andy
Virtually comatose but still standing
Posts: 8716
Joined: Fri Nov 18, 2005 1:00 pm
Location: Ash, Surrey
Contact:

Post by Andy » Wed Mar 15, 2006 9:12 pm

Looks like you've got exactly the same type of boiler as moi!

User avatar
FlippinMental
Hollow Legs
Posts: 337
Joined: Wed Mar 08, 2006 1:00 pm

Post by FlippinMental » Wed Mar 15, 2006 11:01 pm

QUOTE (andy @ Mar 15 2006, 08:12 PM) Looks like you've got exactly the same type of boiler as moi!
any idea what model it is? can't find no markings anywhere on it.

User avatar
Andy
Virtually comatose but still standing
Posts: 8716
Joined: Fri Nov 18, 2005 1:00 pm
Location: Ash, Surrey
Contact:

Post by Andy » Wed Mar 15, 2006 11:06 pm

Mine's a Swan C27 (27 is capacity in litres), there's a plate on the base.

User avatar
FlippinMental
Hollow Legs
Posts: 337
Joined: Wed Mar 08, 2006 1:00 pm

Post by FlippinMental » Wed Mar 15, 2006 11:42 pm

no plate on this one, andy. but it does hold 27ltr. thanks for info. any idea about availability of spares?

User avatar
Andy
Virtually comatose but still standing
Posts: 8716
Joined: Fri Nov 18, 2005 1:00 pm
Location: Ash, Surrey
Contact:

Post by Andy » Wed Mar 15, 2006 11:45 pm

Spares are available but pray the element doesn't go!

http://www.spares2go.co.uk/browse/C27/E ... /p3228.htm

Edit: Available on http://cgi.ebay.co.uk/BURCO-WATER-BOILE ... otohosting also for a bit less wedge.

User avatar
FlippinMental
Hollow Legs
Posts: 337
Joined: Wed Mar 08, 2006 1:00 pm

Post by FlippinMental » Wed Mar 15, 2006 11:55 pm

ouch!!! i'll be taking good care of the one thats in there.

Post Reply